Comments for Support site for JTi products

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Tim

Tim — Sun, 28 Jul 2019 20:00:33 +0000

In reply to Dave. I would say not. Generally, wheel speed sensors work without the mod: it's just a case of setting the thresholds up correctly in SCal.

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Dave

Dave — Sun, 28 Jul 2019 19:35:03 +0000

Thanks Tim

Sorry for all the questions!

I am currently picking up my 2 wire wheel speed sensors using bipolar
These are lotus/Vauxhall wheel packs

Not sure if I would need your hardware mod to pick these sensors up?

Cheers
Dave

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Tim

Tim — Sun, 28 Jul 2019 18:18:02 +0000

In reply to Dave. Absolutely! You can download the User Guide from the Downloads/Technical info page - that will hopefully explain it all.

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Dave

Dave — Sun, 28 Jul 2019 13:54:32 +0000

In reply to Dave.

Hi Tim

Can you confirm that I can use the 4 additional inputs along side the motion sensor data (lateral/longitudinal/vertical G and yaw/pitch/roll). On the S6 GP ?

Kind regards
Dave

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Dave

Dave — Thu, 25 Jul 2019 07:09:51 +0000

Thanks Tim
It’s being used on a Syvecs 6GP so hopefully won’t be too much of an issue.

I will be wanting to use it for the four wheel speed inputs, GPS, and the yaw sensors etc, for aiding traction control

Thanks for the info

Kind regards
Dave

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Dave

Dave — Thu, 25 Jul 2019 06:58:53 +0000

Thanks Tim
It’s being used on a Syvecs 6GP so hopefully won’t be too much of an issue.
Thanks for the info

Kind regards
Dave

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Tim

Tim — Wed, 24 Jul 2019 15:05:27 +0000

There are various ways it can be used, with varying degrees of complexity.

If it’s used as a generic GPS unit on a Life Racing or Syvecs ECU then it is just a case of setting the ECU to expect GPS data, and the MEU to transmit it (a simple checkbox).

If it’s used in Syvecs/Life Racing “Slave mode” (so it behaves as an I/O expander) then some manual configuration of the ECU to receive the data is needed – all explained in the User Guide.

On a Link G4+ or any other ECU it needs manual set up of the ECU to receive the data in the right way, and each ECU type will have its on peculiarities as to what can be set up or not.

And we’re always here to assist.

Comment on New Mini-Expansion Unit Software – GPS and Speed Sensor Enhancements by Dave

Dave — Wed, 24 Jul 2019 14:54:52 +0000

Is there much software manipulation to get the gps unit working?
I know my way round it a little but not that clued up on everything

Kind regards
Dave

Comment on Part Numbers by Tim

Tim — Sun, 05 Oct 2014 10:30:31 +0000

V1.40 did not seem to sort this issue and further investigation revealed that the CAN definitions for the Syvecs were not 100% correct.

Grabbing the file from the downloads section of this site and applying it to the CAL – problem solved 🙂

Comment on Part Numbers by Tim

Tim — Thu, 02 Oct 2014 08:54:53 +0000

In reply to paul.

There have been some issues with LC indication with it getting broken, then fixed, then broken again, in versions between V1.30 and V1.35. There is a new version V1.40 available that – we hope! – puts this issue to bed.